Sunday, December 27, 2009
Wednesday, December 23, 2009
Sunday, December 20, 2009
BILL OF MATERIAL
DUALPULSEbom4
Please note that the following components were used for version 1 and are not necessary to install for version 2.
Q1, Q2, Q3,
D6, D7
U4
R4, R8, R9, R10, R12, R13, R27
C9
Please note that the following components were used for version 1 and are not necessary to install for version 2.
Q1, Q2, Q3,
D6, D7
U4
R4, R8, R9, R10, R12, R13, R27
C9
Saturday, December 19, 2009
Finished Dual Pulse Welder
The oscilloscope photo above shows a 12.6 Volt, 5Ms and 15.1Ms weld. Both pulses and the charge times is measured between the two purple lines and is 189Ms which is more than 5 welds per second at this setting.
Sunday, December 13, 2009
Photo's
Left to right : Pulse1, Pulse2 and Voltage adjustment
This took me way longer than expected and I was hoping to have it done by the end of this weekend. The aluminum brackets that the pcb's are on took me most of Saturday to make. I broke two brackets before getting it right and then had a hard time mounting the pcb without making a short. I finally cut all my hard work off and put a piece of wood between the the two cut offs. Bending, drilling and fitting the copper bars took up all of today.I did however test the dual pulse before tackling this job and I am very pleased with the results. It works better than expected and you can use any one of the two pulses by turning anyone off or use both. At this moment you get two bleeps when you use the dual pulse and one bleep when you use one pulse, it is very fast though and sounds more like a long and a short bleep. It's things like this that needs a little attention.
I will try and have it finished by next weekend and hopefully get it on youtube.
Sunday, December 6, 2009
Just a quick update
I'm done writing the code for the dual pulse and ran it on a simulator but haven't tested it on the welder yet. I took my old welder apart and are in a process of building the new design into that box. I had to cut the Mosfet board and the heat sinks smaller to fit and will post the pictures when I'm done. I was looking into using Joules and Watt Second and not time to control the welder and I will definitely use that to control this welder with a version 3 chip after this one.
What is the difference? Joule and Watt Second will look at the resistance and adjust the time automatically to make better controlled welds and preventing burning holes when the pressure on the electrodes are not same. It will also give you the exact energy release when you are welding different resistances.
What is the difference? Joule and Watt Second will look at the resistance and adjust the time automatically to make better controlled welds and preventing burning holes when the pressure on the electrodes are not same. It will also give you the exact energy release when you are welding different resistances.
Tuesday, December 1, 2009
ALMOST DONE
Well, I'm busy with the dual pulse code for the processor and also a couple of bugs that is p***ing me off :)) I guess everyone is asking "why so many Mosfets?". Many Mosfets in parallel lowers the resistance that lowers the heat and increase the amps. The difference between six of these Mosfets and eighteen is a couple of hundred amps more and a welder that is not going to overheat and burn out. You can also see that I get excellent controlled welds at much lower energy rates than commercial welders out there. I'm also turning this Mosfets on and off at precise calculated speeds according to the data sheets to prevent them from going up in smoke.
I'm in the process of ordering more boards and will hopefully be done with the programming by the time they come in to make it available to you guys.
Thursday, November 26, 2009
CHARGING SPEED
The voltage on the left is the actual capacitor voltage and the voltage on the right is the set point. This was just a test with a 19Ohm resistor connected to the discharge terminal causing the discharge to be very slow when the set point is lowered. This will be much faster with a resistor bank with a lower resistance.
Sunday, November 22, 2009
PCB TEST
I've spent this weekend putting the new PCB together( I actually had it built before Friday) and it was very easy to build. You will need magnifying glasses, a good light and a hot air soldering iron for the surface mount components. The rest of the components are soldered at the bottom side and the solder gets pulled into the holes so no soldering is necessary at the top. There are two problems however, I screwed up on the solder mask on the Mosfets and you have to scratch the mask off around the solder points to get a bigger solder area and Diode 10 needs to be turned around.
The charging speed is so fast with a 12 Amp supply that when the capacitor reached it's set point and the mosfet kicks in when the voltage drops 0.1V that it actually overshoots the set point by 0.4V before turning the Mosfet off. I've been writing some really complicated code to try and fix this issue.
Tuesday, November 17, 2009
THE PCB'S ARRIVED
Well, the PCB's finally came in. I have a very expensive camera and as you can see I'm not very good with taking photo's. This board is very solid and absolutely of high quality. I don't know why, but my camera makes the middle of the board look like its bent and some of the silver on the board look like it's black.
I will build this board this weekend and post more photos.
Saturday, November 14, 2009
Subscribe to:
Posts (Atom)


